About

LCD_Config is a hardware and software solution to program the Multi Wii Copters on flying field, also it contains the possibility to log data while flying and playback the log files to the MultiWiiConf.

Features

works for Multi Wii Software 1.5 (stable) and 1.6pre
serial communication with the MultiWii software
same parameters changeable as in the GUI
presents sensor data (gyro, nunchuk, acc, barometer), receiver input channels, abd output channels (ESCs and servos)
simple graphic output for servo channels and inclination angles
logging to SD cards
profile management to test different settings

Prerequisites

an Arduino board Arduino Boards
Arduino 022 (for SD Card support)
a LC Display, either using parallel 4 Wires or ShiftReq control (based on the Hitachi HD44780 (or a compatible) chipset, which is found on most text-based LCDs.)
Some keys, some cable
latest Arduino Sketch for LCD_Config

Download

(Note: the version of the LCD_Config does not correspond to the version of the MultiWiiCopter software. All listed versions of the LCD_Config work with both MWC v1.5 and v1.6pre.)

V1.50: http://www.rc-heli-fan.org/download/file.php?id=92207

V1.60: http://www.rc-heli-fan.org/download/file.php?id=92263

V2.0 beta: http://www.rc-heli-fan.org/viewtopic.php?f=255&t=80336&start=315#p1186998

V2.0: http://www.rc-heli-fan.org/viewtopic.php?f=255&t=80336&start=375#p1190414

V2.1: http://www.rc-heli-fan.org/viewtopic.php?f=255&t=80336&start=420#p1193837

V2.2: http://www.rc-heli-fan.org/viewtopic.php?f=255&t=80336&start=450#p1197679

V2.3: http://www.rc-heli-fan.org/viewtopic.php?f=255&t=80336&start=480#p1201705

V2.4: http://www.rc-heli-fan.org/viewtopic.php?f=255&t=80336&p=1205571#p1205571

V2.5: http://www.rc-heli-fan.org/viewtopic.php?f=255&t=80336&start=480#p1208770

V2.6: http://www.rc-heli-fan.org/viewtopic.php?f=255&t=80336&p=1212892#p1212892

Version History

V0.8 to V1.4 see [1]

V1.50

check trailing 'A' char in serial communication to detect frame errors,
KEY_LEFT cancels reading when no serial connection is present (important to reset wrong settings!)
optimization of format routines (merged two routines, invalid values are displayed as ###)
bugfix in logging (logMode=-1 was stored in flash, so logging was permanently disabled)

V1.60

Min/max values show up again (optional)
Fixed some issues on compiling with different options

V2.0 beta

Adaptation to MWC version 1.preter6 (new config "Flying Wing", new data format)
Changed arrangement of parameters in state "0 - Config"
Bug 'logMode=-1' finally solved

V2.0

Swapped motors 4 and 5 in 'Esc Out' for versions 1.5 and 1.6prebis
Changed behaviour of UP and DOWN for consistency (UP decrements, DOWN increments values)
Added version V1.6
Output logfiles in LogView format [OPTIONAL] (file numbers starting from 500, extension ".lvw")
Added JOYSTICK option to replace input buttons by an analog joystick [experimental]
Display 'invalid' values in graphics
Heavy optimizations (!) due to space restrictions
Removed WAIT_FOR_INIT option, changed start state to 31 instead

V2.1

Bugfix in deserialize() with v1.6
Joystick handling was improved (calibration, use of pullups, can be used in parallel to buttons)
Added 'Play LogFile' state
Easter egg function to display internal configuration :)
BUGFIX: RC Rate multiplied by factor 2 for MWC Versions >v1.5, minimum of 20% for RC Rate (0% makes no sense)
Added random offsets in TEST mode

V2.2

Cancel in Logfile Playback (press LEFT_KEY)
Settings of "Baud Rate", serialRead() has been adapted to work with different COM speeds
Greater flexibility in changing the Settings
(Log) Delay Time was moved to Settings state and is used as the time interval of polling the MWC board

V2.3

Changed internal representation of state machine and strings
Support for v1.7pre (I-/P-Level instead of AutoLevelStrength, trigger calibration, 8 instead of 5 receiver
channels, configuration of activation modes for Aux1/Aux2, ...)
Software Version is now stored in Logfile
APC220 Option (disables APC220 module via pin D2 during playback of logfiles, experimental)

V2.4

Swapped Angle and Baro/Comp/Cycle states
Added 'Config' parameter to LogFiles, show Config and Version in selectLogFile
Use of blinking Cursor instead of Arrows in Enter mode
LogView mode: corrected order of receiver channels
Greater robustness in serialWrite() method

V2.5

Simultaneous setting of Roll and Pitch PID values ("2 PID -> Roll/Pitch")

Hardware

LCD Keypad Shield

This is the original LCD used with the LCD_Config app:

Schematics: http://www.nuelectronics.com/estore/index.php?main_page=project_lcd

4bit parallel Display and voltage divider keys

Joystick

Emulation of the four required input buttons via an analog Joystick (like the one used in Wii Nunchuks). Requires two analog input pins and (optional) one digital or analog input pin for the Select key.

Hardware Keys

If you like to use normal hardware keys on digital ports use this schematic to connect them:

http://arduino.cc/en/Tutorial/DigitalReadSerial

Then remove the comment signs // in front of line:

#define HWKEYS

Define the ports to use here:

// Input pins of the hardbuttons: (used when HWKEYS is defined)
#define HW_RIGHT    10
#define HW_UP        9
#define HW_DOWN     11
#define HW_LEFT      8
#define HW_SELECT    6

It is possible to controll everything with out the Select key, so you don't need this key.

Shift Register LCD

Using 3 wires interface for the display:

http://www.arduino.cc/playground/Code/LCD3wires

Adjust the ports used here:

  ShiftRegLCD lcd(3, 2, 4, 2);        // (Datapin, Clockpin, Enablepin or TWO_WIRE [, Lines [, Font]]])

Logging

Connection of SD Card: standard SPI interface, i.e.,

pin 13   SCK   SPI clock   
pin 12   MISO   SPI master in, slave out
pin 11   MOSI   SPI master out, slave in
pin 10   SS   SPI slave select

Logfiles are written either in binary format, in that way they can be sent to and visualized by the MultiWiiConf software, or (starting from Version 2.0) in LogView OpenFormat, to display them in LogView. A corresponding device file for LogView (.ini) is included in the archive beginning from Version 2.0. For more details, check out www.logview.info (and don't forget to donate :)).

Status LEDs

Primary goal of this option is to give some visual feedback on the internal state when no LCD is connected. Three LEDs are supported, named RED, YELLOW and GREEN (like a traffic light).

The red LED signals errors (slow flashing, e.g., when the application is halted), or recoverable exceptional states (fast flashing, e.g., the app is waiting for input from the serial connection).

Yellow LED: blinking means I/O, it is permanently on when the app is waiting for user input

The green LED signals logging.

LEDs are connected through 220-500 Ohm resistors to some of the unused ports (default: A1 - Red, A3 - Yellow, A5 - Green).

Port settings are defined here:

// include routines to show the state of the application with three leds 
// (red: error, yellow: busy/waiting for input, green: logging)
#define STATUS_LEDS

#define RED_LED      A1
#define YELLOW_LED   A3
#define GREEN_LED    A5